The Spawn is On

Dsc_0014

Well, it’s that time of year again. The fish are moving up and are starting to cruise the shallows. I have already seen a couple of bed fish, and have seen some pretty aggressive males. With the full moon this week, there should be a whole wave of new fish coming up and starting their migrations into the spawning areas. With this in mind, I have started to put together a bed bait box, and I thought I would share my thoughts.

Like everything else, I try to keep my approach simple. But unlike other fishing techniques I think it is more important to keep your gear ready at a split second’s notice during the spring time. I usually have 3-4 rods rigged up on the deck of my boat for fishing beds. All bass on beds act differently. I like to move in very slowly, and watch the fish long before I even think about casting. There are a handful of things I am looking for:

  • A flare of the gills, a dash towards the bait, actual contact with the bait, picking up of the bait, versus complete disinterest in the bait – this will help you determine whether or not to pursue the fish.

  • The sweet spot: most all beds have one small spot that really pisses the fish off pretty badly. It can be as big as a couple of feet, or as small as a couple of inches. Most of the time, this is going to be somewhere near where the fish return and centers on the bed, and the most likely place for a strike.

  • Entrance & exit: most fish will enter and exit from specific spots on a bed. First you want to determine these spots, and make sure you don’t block their cruising areas if they do get worked up and leave the bed.
    Location: This will determine how you set up an approach to fishing a particular bed.

  • Location of the sun: Try and keep the sun at your back, but at the same time make sure not to cast a shadow over the bed. This puts you more in the fish’s blind spot.

  • Stealth: be a quiet as possible when stalking bedding fish. Keep your trolling motor use to a minimum. Do everything you can to not create a trolling motor wash towards the bed. And in shallow water, use a push pole if you can.

  • Slow down: I know it’s hard to do when you spot some of the big fish you see on beds, but if you are not patient, most of the time the fish will win.

  • Baits: One of my favorite baits without a doubt is the Matt Lures Bluegill. I like to start with this bait to establish my relationship with the fish. Another bait that I have already used on some bed fish and have already gotten a great response from is the River2Sea Nest Raider.

    I’ll swim the bigger baits through the area and see what kind of reaction I get. If the fish are super hot, sometimes you’ll catch them right off the bat. Most of the time, though, this is not the case. This is the reason I like to keep those rods on the deck, rigged and ready to go. This lets me get another bait in the water in that critical moment, when a fish may be worked up. A lot of time you will have to play around with different baits, to see what really makes them mad. Some of my secondary baits include a jig, a Huddleston Huddlebug crawdad, a Senko, and sometime even a small worm or drop shot. I like to use big stout hooks with all of my bed baits. Because you usually only get one chance at a hook set.

    Drive the hook home pretty hard, and make sure you always have the net ready. These bass are usually pretty unhappy.

    I really like bed fishing because it can be such a head game between you and the bass.
    July_cats_n_bass_n_boats_07_125

  • Questions, Comments

    I have been working pretty hard on getting my swimbaits into production and keeping the site updated. Please let me know what you think of the site so far, you can leave comments or just e-mail me, also if you have any article Ideas or questions. There is an e-mail link at the top right of the site.
    Thanks everyone….. Josh St.John

    Google Earth For The Bass Fisherman

    What it is:
    Satellite images of anywhere on Earth at the click of a mouse. Google Earth is a download that runs a web program on your computer that lets you access constantly updated satellite images.

    Why you want it:
    Bird’s eye views of any lake, anywhere: Fishing a new lake next weekend? Check out the shallows, weed beds and points ahead of time. Investigate where the last tournament winner caught the big fish last time. Thinking about a peacock fishing expedition in the Amazon basin? Zoom in and plot a plan of attack.

    Plus:
    The tilt feature allows you to swivel down and get a topographical view of your destination.
    Photos and notes added by other users provide extra detail
    Print out overhead views for use on the lake

    Add notes: Make it your own: add notes or your own photos to GoogleEarth. You can choose to share them or keep them private, just for your own use.
    Link

    “My Places” you can mark places on your Google Earth that you want to revisit or remember
    Link

    Synch it up with your GPS unit
    Link

    Find out more here
    Link

    Biting Off More Than He Could Chew

    One afternoon last year on Lake Sonoma, I was quietly casting when I heard some splashing behind me, so I went over to see what it was all about. As you can see in the pictures below, what I found was this fish floating and twitching on the surface – a bass literally dying on the surface with a bluegill completely wedged in its mouth. I pulled the joined pair out of the water. Both were very pale from lack of oxygen, so I separated them quickly and let them both swim off. It’s one of those things I could hardly believe even though I was seeing it. Now, I have caught a lot of fish with small fish half digested in their throat before – even to the point of still hanging out of their mouth. But never quite like this.

    Now it really makes me wonder every time I catch a 2 to 3 pounder on a Hudd or any other big bait – how often does a little fish like this bite off more than he can chew, and we never know?

    Img_0644_2

    Img_0645_2

    How to Make Your Own Big Topwater Plug Bass Lure

    As promised: here is a ‘how-to’ on wooden plug making. The process is pretty easy, and it can be rewarding catching fish on a bait you have made yourself.

    I’ll start by talking about materials, wood types, and tools needed. I prefer to use a few types of wood for my baits: cedar, poplar, basswood, pine, and balsa. These are all soft, highly buoyant woods that are great for top water plugs. E-bay is a great source for pieces of wood without ever leaving home.

    Dsc_0002

    First and foremost you will need a lathe to start off your lure, or a round piece of wood such as a pine dowel. These can be purchased at just about any hardware store. Here is a link to Harbor Freight. They sell a lathe-6” sander combo for only $100. The quality won’t be the best in the world, but if you consider that most plugs sell from $20-$50, it will pay for itself pretty quickly.
    Harbor Freight Lathe/Sander
    You can also buy premade plugs such as these:
    Plugs

    Shaping above and beyond this is totally up to the lure maker-the possibilities are endless. This is the point at which you will want decide what you will be using for a tail. Just open up any one of your worm boxes and the ideas will start flowing. I am using a large fluke-style tail on mine. This will determine the closing tail size and shape of your bait.

    Dsc_0006

    Some tools to help shape your lure further are a 6” electric sander, various files, 80 grit sandpaper (you will be surprised how fast these materials work down), and maybe an Exacto blade or wood carving set for detail. I usually finish sand with about 150 grit and then work down to 400.

    As far as hardware supplies for your lures, here are few choices:

  • Jann’s NetCraft
  • LureCraft
  • Stamina, Inc

    You will need hooks, hook eyes, paint, clear-coat or epoxy coat, eyes, some sort of a tail (worm or small swimbait).

    Dsc_0015

    I have made a jointed bait here, but you can also make single-piece topwater plugs. If you choose to make a jointed bait here is a simple method. Choose your joint area and mark a 30 to 45 degree V to be cut. This can be done on a band saw or by hand using a small miter box. I used a marker here so you could see it well in the photo; however you will not want to do this as it will bleed through the final paint. Once you have cut the V you will need to cut a receiving slot for your eye hook. Make this with the band saw or by hand again. Drill a small hole and insert a pin. The pin should be made out of a stainless piece of rod so it will not rust. Remember to drill the hole just a tad smaller than the rod so it can be hammered in tight. You can also use a galvanized nail for this pin.

    Dsc_0024

    Next, decide if you want to add a lip or not. Adding one will give the bait more wobble. If you choose not to it will make for more of darting bait. Lips can be purchased at some of the above mentioned sites or cut out of a small piece of plastic from the hardware store or hobby shop. Cut a slot for it and epoxy or super glue it in place.

    Dsc_0030

    Dsc_0035

    The eye hooks can be put in now or after paint. I usually prime my baits with an automotive primer. You can get this in a small can at a local automotive store, or DupliColor makes some good spray can products. The above lure suppliers will also sell various paints. The baits can be spray painted, hand painted, or airbrushed – whatever you have available to you. The possibilities are endless here. Once you are done, add some clear paint or epoxy to seal the deal and you’re ready for hooks and some topwater action. I will do a post on the steps of painting a bait next week.
    Dsc_0063_2

    Things you will need:

  • lathe and wood stock, dowel, or blank
  • sander
  • files
  • sandpaper
  • paint
  • hook eyes
  • stainless rod or nail
  • eyes
  • plastic for lip
  • tail

  • Clear lake Swibait testing

    Dsc_0016

    So after a couple days of fishing Clear Lake I have got a small list of final adjustments to be made to the new swimbait. Unfortunately the Swimbait bite on Clear Lake is still slow, to say the least. Two days, two small fish. The bait is working great though, a good slow steady horizontal fall on the slow sinker and great turning action on the floater as well as the sinker. I am just trying to figure out my final color schemes. I am leaning towards ayu, hitch, silver shad and trout.

    AnglerTech: YouTube for Anglers

    When ESPN and the Outdoor channel let you down, and you are jonesing for your bass fix, check out the offerings online on YouTube – I was surprised at how much there was up for the bass aficionado.

    The beauty of YouTube is not just the stolen clips from commercial TV, but also the classic clips you can’t track down anywhere else outside of a rummage sale, but even more importantly the fact that anyone, anywhere with the barest minimum of video equipment can effectively have their own broadcast channel.

    So who’s using it? Pros. Guides. Bait companies showing off their latest tests. Bass fishermen of all stripes and regular guy anglers who just want to share their video from their local lake with their buddies.

    Try these searches for a start:
    Underwater Bass Fishing
    Swimbait
    Bill Dance

    and especially this one. It doesn’t get any better than that.

    You can also try searching the name of your local lake, your favorite pro, or tournament series, and you are almost guaranteed to get results.

    The best part about it is that you can make it better by adding to it yourself. It doesn’t take much to make a YouTube video, and it’s free and easy to use. If you do upload your own videos, let us know, and if it’s cool, we’ll post it here, too.